J1939 Wheel Based Vehicle Speed not working

Discuss issues and ideas you have to configuring displays with PowerVision
vom1rhi
Posts: 14
Joined: Mon Oct 10, 2011 2:26 pm

J1939 Wheel Based Vehicle Speed not working

Post by vom1rhi » Thu Nov 03, 2011 1:33 pm

Hi Everybody!

I have a fwMurphy PV450 Display, programmed with PowerVision 2.3
Today was the first time we tested the display in a vehicle, and nearly everything worked fine.
We had Open Can Messages and some standard J1939 signals.

Unfortunately, the Wheel Based Vehicle Speed didn't work. Not with my setup, and not with the Standart fwMurphy Configuration in Powervision 2.3

I used the standard setup, which is already in the PowerVision software.

Can somebody help me, to get the speed working?

I attached screenshots, so you can see my config!

Thanks
vom1rhi
Attachments
J1939_Programming_vom1rhi.jpg
J1939_Programming_vom1rhi.jpg (238.88 KiB) Viewed 128 times
J1939_PageDesignerTextGauge_vom1rhi.jpg
J1939_PageDesignerTextGauge_vom1rhi.jpg (90.9 KiB) Viewed 128 times
J1939_EnviromentSetup_vom1rhi.jpg
J1939_EnviromentSetup_vom1rhi.jpg (192.79 KiB) Viewed 128 times
bmcrae
Enovation Controls Development
Enovation Controls Development
Posts: 75
Joined: Thu Sep 09, 2010 11:20 am

Re: J1939 Wheel Based Vehicle Speed not working

Post by bmcrae » Thu Nov 03, 2011 1:52 pm

It looks like you expect Wheel Based speed to be transimtted from a device at CAN address 3. So is there is a different device beside the engine transmitting Wheel Based speed parameter?
vom1rhi
Posts: 14
Joined: Mon Oct 10, 2011 2:26 pm

Re: J1939 Wheel Based Vehicle Speed not working

Post by vom1rhi » Thu Nov 03, 2011 2:03 pm

No I didn't expect that, it's just, what was in the standard config
RPM for example worked!
But it must be something with the address, because our ECU is getting a signal, but not the display
As you can see on the screen, we are just using CanPort1, but I am not sure, which address to take!
Hope that was helpful for you. If you have more questions, please let me know
vom1rhi
Posts: 14
Joined: Mon Oct 10, 2011 2:26 pm

Re: J1939 Wheel Based Vehicle Speed not working

Post by vom1rhi » Thu Nov 03, 2011 2:13 pm

I am not totally sure, what information you need actually.
We receive our signals from CANPort1
We have an ECU, which can read and use the Wheel Based Vehicle Speed.
But I am not familiar with that config.

I took CAN address 3 because it was there as default.
If you suggest a different address, please let me know

Oh, and for example the RPM worked
jdgallaher
Enovation Controls Development
Enovation Controls Development
Posts: 9
Joined: Tue Sep 14, 2010 11:30 am

Re: J1939 Wheel Based Vehicle Speed not working

Post by jdgallaher » Thu Nov 03, 2011 2:55 pm

I noticed that the variable for the Text gauge was Calculated VehicleSpeed, yet the J1939 parameter was J1939.Transmission.Wheel Based Vehicle Speed. This may be your problem.
vom1rhi
Posts: 14
Joined: Mon Oct 10, 2011 2:26 pm

Re: J1939 Wheel Based Vehicle Speed not working

Post by vom1rhi » Thu Nov 03, 2011 2:58 pm

Oh that's a wrong screen shot
Beside the Wheel Based Vehicle Speed, I am calculating the vehicle based on the Output Shaft Speed and some other variables, but that's not working to, unfortunately
bmcrae
Enovation Controls Development
Enovation Controls Development
Posts: 75
Joined: Thu Sep 09, 2010 11:20 am

Re: J1939 Wheel Based Vehicle Speed not working

Post by bmcrae » Thu Nov 03, 2011 3:07 pm

I would suggest adding the parameter to the engine device (at address 0) which is the ECU. Maybe the ECU is transmitting this parameter. Typically what we see is the use of a sendercan or XM500 that picks up these parameters and then translates them at a specific address and parameter into J1939.
vom1rhi
Posts: 14
Joined: Mon Oct 10, 2011 2:26 pm

Re: J1939 Wheel Based Vehicle Speed not working

Post by vom1rhi » Fri Nov 04, 2011 1:16 pm

I tested the vehicle today again, but nothing worked with the speed
I added the WBVS (Wheel Based Vehicle Speed) to the engine device, and still, nothing has changed, I also tried a few different addresses but no success.
But the Engine Speed is working perfect, that's whats funny

Oh and by the way, fuel level isn't working to.

Does anyone have further suggestions, how to get this working?
vom1rhi
Posts: 14
Joined: Mon Oct 10, 2011 2:26 pm

Re: J1939 Wheel Based Vehicle Speed not working

Post by vom1rhi » Fri Nov 04, 2011 2:30 pm

And as an additional information, we found out, that we have an extended frame (29-bit) for the Wheel Based Vehicle Speed
Does this mean, that I will have to create an Free Form Can Message or can I change the standard J1939 settings?
Beside that, can you tell me the settings for the Free Form Can Message to read Wheel Based Vehicle Speed?

Thanks
vom1rhi